کیان تدبیر ژرف اندیش پاژ

کیان تدبیر ژرف اندیش پاژ
شرکت کیان تدبیر ژرف اندیش پاژ تولید کننده تجهیزات صنایع نفت و گاز

آدرس: مشهد- پارک علم و فناوری خراسان- ساختمان موسسات فناور و دانش بنیان - واحد 216
تلفن : 35425583-051
نمابر : 35425584-051
همراه : 09150085583
تلگرام : 09150085583
کارخانه : 35425525-051

۱ مطلب با کلمه‌ی کلیدی «شیرهای ایمنی تحت استانداردBSI» ثبت شده است

دوشنبه, ۳۰ ارديبهشت ۱۳۹۸، ۰۵:۰۴ ب.ظ

استاندارد

Safety Valve Codes & Standards

Safety and Relief Valves are completely governed by codes and regulations. The two major codes are ASME (USA) and PED (Europe), and both are laws and failure to comply is a criminal offence. As you would imagine, they are both very similar but also do have some distinct differences. Because the codes are law, they must be adhered to when equipment is installed in a specific region. Most manufacturers therefore have both approvals. When installing a safety valve however, to be compliant with these codes you not only need to use an approved supplier, but you also need to select settings, and install them in accordance with the codes.

The governing standards and recommended practises are API 520 (USA) and EN4126 (Europe). API 520 incorporates more detail on correction factors (more conservative) for back pressure and viscosity, hence is the most widely used for valve sizing.

Europe

  • PED 97/23/EC - Pressure Equipment Directive - Classifies pressure equipment into four categories (I, II, III, IV)
  • EN4126 - Safety devices for protection against excessive pressure

USA

  • ASME I - Direct fired pressure vessels
  • ASME III - Nuclear power plants
  • ASME IV - Heating Boilers
  • ASME VIII - Unfired pressure vessels
  • ANSI/ASME PTC 25.3 - Performance test codes
  • API 520 - Sizing selection and installation of pressure relieving devices in refineries, Part 1 Design, Part 2 Installation
  • API 521 - Guide for pressure relieving and depressurising systems
  • API 526 - Flanged steel pressure relief valves
  • API 527 - Seat tightness of pressure relief valves

Some Others

  • Korea - KS B 6216 Spring loaded safety valves for steam boilers and pressure vessels
  • Japan - JIS B 8210 - Steam boilers and pressure vessels - spring loaded safety valves
  • Australia - SAA AS 1271 - Safety valvces, other valves, liquid level gauges and other fittings for boilers and unfired pressure vessels
  • International - ISO 4126 - Safety valves - general requirements

The European PED, from a legal perspective replaces the very many local codes in all European member states such as BS (UK), TUV (Germany), AFNOR NFE (France), Stoomwezen (The Netherlands), ISPESL (Italy).

Some European users may also stipulate their local code however in addition to the PED. Local codes have different ways of presenting things but often the results are the same.

Compliance with the PED allows a manufacturer to CE mark their product.

Further information on ASME and API

ASME B16.34 - Applies to valves with flanged, threaded, and welding ends: This standard covers pressure/temperature ratings, dimensions, tolerances, materials, non-destructive examination requirements, testing and marking. This standard is not specifically applicable to Safety Relief Valves but is often used by manufacturers as good engineering practice.

ASME B16.5 - Applies to pipe flanges and flange fittings: Provides allowable materials, pressure / temperature limits and flange dimensions for standard ANSI flanges.

ASME Stamps:

ASME itself does not certify the valves. This is done by a National Board (NB) and they certify the valves capacity and the valves complaince with the ASME code. It is then published in the "Red Book" - NB18, along with the true flow co-efficients as measured and approved by them.
موافقین ۰ مخالفین ۰ ۳۰ ارديبهشت ۹۸ ، ۱۷:۰۴
هادی مکاری